AdaptiveSync Cont: G2G, Ghosting, & Pixel Response Times

Last, but not least – and certainly the most interesting – AdaptiveSync compliance also requires passing a battery of tests for pixel response times and overdrive overshoot/undershoot (i.e. ghosting). In fact, this is an area where VESA is being especially methodical, as not only is the group concerned with the image quality problems that come from ghosting, but they’re also putting their foot down on shenanigans involving Gray To Gray (G2G) pixel response times. As a result the pixel response time tests are geared to not only identify excessive ghosting, but they also define a very rigid (but sensible) test for measuring G2G response times.

For pixel response times, VESA is not so subtly taking aim at manufacturers’ current state of measuring and promoting G2G pixel response times, which can get creative at best, and exaggerative at worst. But despite those shenanigans, G2G response times remain an important metric: because G2G pixel transitions are some of the longest ones for LCD pixels (as opposed to black-to-white), they are the de facto standard for measuring overall response times. So as part of their overall pixel response time and ghosting testing for AdaptiveSync, VESA also needed to set a standard for measuring G2G response times.

The resulting methodology is essentially G2G testing with all of the shenanigans stripped out to avoid cherry-picking results. Among other things, VESA’s test requires an ambient (room) temperature of 22.5 to 24.5 Celsius (72.5F-76F) and that a panel has reached its equilibrium temperature. This is because the response times of liquid crystals varies with the temperature, and thus a display can produce unnaturally good times if the panel is heated. The size of the heating effect is actually rather surprising: according to VESA, they’ve seen some displays halve in response times just by increasing the ambient temperature by 5.5C.

Meanwhile, to avoid favoring any one G2G transition, VESA’s G2G testing instead involves averaging the results of 20 transitions amongst 5 different grey levels (black, dark grey, mid grey, light grey, white). This does mean that the resulting value is going to be better than the worst-case transition, but it also means that the resulting value will be worse than the best-case transition; on average, it balances out. Overall, an AdaptiveSync display requires an average G2G response time of less than 5ms, which is more than fast enough for a full transition on a 144Hz display with time to spare.

And, of course, the test looks at how well a display hits its target pixel value in order to ensure that the pixels aren’t being overdriven/underdriven by too much, which would result in visible ghosting. AdaptiveSync conformance requires that the highest G2G overshoot is under 20%, while the highest undershoot is even tighter at less than 15%. This is another case of the standard using perceptual boundaries, as a perfect result is all but impossible with overdrive, and a fast display is not possible without overdrive.

Notably, all of this testing is once again done with factory settings on a display. So although a display can offer multiple overdrive settings to satisfy a user’s preferences, the out-of-the-box mode needs to be the balanced mode, producing reasonably fast pixel response times without causing either ghosting (undershoot) or inverse ghosting (overshoot).

Variable Overdrive: Unneeded?

With all of that said, the pixel response time test does have a notable omission that monitor aficionados (and NVIDIA employees) will likely pick up on: variable overdrive testing. VESA’s testing does not explicitly test for overdrive at explicitly varying refresh rates, rather their testing is done in Adaptive-Sync mode which will have a display updating its pixels at what’s essentially their maximum refresh rate (e.g. 144Hz). It’s something that VESA has apparently put quite some thought into, as there’s actually a rather informative note about it in the AdaptiveSync Display FAQ:

When running in Adaptive-Sync mode, the refresh rate (i.e., the speed at which the data is transferred, frame by frame, to the display) and the speed at which the display scan out is occurring is always at maximum refresh rate. When frames are being updated at less than the maximum refresh rate of the panel, this is not because the panel is running any slower, but because the vertical blanking interval (VBlank) timing between frame to frame has increased. Therefore, there is no reason to test G2G/Overshoot/Undershoot at anything other than maximum refresh rate as that’s the only rate the panel will be operating at when in Adaptive-Sync mode. If you were to exit from Adaptive-Sync mode and change the display timing to a fixed rate timing, then and only then does the display clock rate and scan-out time change, at which point different G2G performance may occur. However, this is outside of the Adaptive-Sync mode and not included within the VESA Adaptive-Sync Display test.

In short, VESA believes that testing response times at multiple refresh rates is unnecessary, because in Adaptive-Sync mode displays should always be updating pixels at their maximum rate so that they’re ready for the next frame ASAP. This is a very interesting point, and one that will warrant a further look once there are monitors available that have passed the AdaptiveSync display conformance test. In the meantime it should be noted that this also doesn’t preclude displays using variable overdrive, as a display could implement it and still pass the conformance test.

Past that, variable overdrive has been a major component of NVIDIA’s G-Sync marketing for years now – and remains the differentiating factor between G-Sync (module) displays and G-Sync Compatible (VESA Adaptive-Sync) displays. So if VESA is right, then that could undermine the advantage (market or otherwise) of displays using NVIDIA’s G-Sync module.

AdaptiveSync: Supplementing Freesync & G-Sync

Finally, it’s worth emphasizing that the AdaptiveSync display standard is solely about setting performance metrics for variable refresh (Adaptive-Sync) displays. It doesn’t cover color gamuts, maximum brightness, viewing angles, or other image quality factors beyond those that relate to variable refresh operation (flicker, ghosting, etc).

And while VESA is focused on its own matters, it’s pretty much impossible to discuss AdaptiveSync without also discussing AMD and NVIDIA’s programs. While VESA is clearly looking to bring a bit of order (and transparency) to the process with their own standard, they’re not necessarily looking to usurp Freesync or G-Sync. Indeed, it’s fully within the allowances of the program that a monitor can be certified for both AdaptiveSync and a third-party variable refresh standard – or even both of them, making for a triple threat monitor.

But if we had to compare AdaptiveSync to the existing standards, at a high level AdaptiveSync looks fairly comparable to AMD’s FreeSync Premium and NVIDIA’s G-Sync Compatible standards.  This isn’t terribly precise comparison since VESA is much more forthcoming about its response time and flicker requirements than AMD or NVIDIA, but at a minimum these are the tiers that all require a wide enough refresh range for LFC, as well as all of the flicker testing all three groups do.

Meanwhile I’d be remiss not to mention Intel here, who is in the process of (at last) rolling out their own contemporary discrete GPUs. Intel only gained variable refresh rate support in 2019 with the release of Ice Lake (10th Gen Core) SoCs, and as a result they currently only have a minimal stake in variable refresh displays. None the less, it’s not to Intel’s benefit that the current certification programs for Adaptive-Sync displays are run by their competitors, so VESA taking on the task in an industry-neutral fashion helps them as well by giving them a certification logo and product database they can point customers to. And over the longer run, Intel stands to benefit even more from the MediaSync display standard, since that’s likely to become a big deal on Intel’s core consumer market of laptops.


Shifting gears, let’s talk about VESA’s other new Adaptive-Sync performance standard, MediaSync. As opposed to the high-end AdaptiveSync spec, MediaSync is far more low-end, focused on ensuring proper variable refresh rate operation for media playback and only media playback. This standard doesn’t have any gaming-centric tests, and while the testing methods are shared with AdaptiveSync, that’s about where the similarities end.

The MediaSync display standard, in short, is a much narrower specification focused around an equally narrow refresh rate range of 48-60Hz. This is the golden zone for media playback, as it’s wide enough to cover everything from movies (23.976fps) and PAL TV (25/50fps) to full speed (60fps) PC content. As well, the standard has the same no-perceptual-flicker requirements as AdaptiveSync, and MediaSync-certified displays will still need to meet the same 20%/15% overshoot/undershoot requirements to ensure there isn’t any ghosting even at these lower refresh rates.

The big impetus behind MediaSync, beyond getting rid of display flicker, is putting a stake in jitter due to the mismatch between typical media framerates and PC display refresh rates. With most professional media content authored to 23.976, 3:2 pulldown jitter has been an issue for PCs for as long as they’ve had media playback capabilities. And since resolving it requires a relatively small range of refresh rates, variable refresh rate tech has always been well-primed to solve the matter.

In terms of technical specifications then, this means that MediaSync displays are limited to 1ms of jitter – frame-to-frame jitter must be no more than +/- 0.5ms. The spec, in turn, tests 10 different frame rates ranging from 23.976fps to 60fps, with testers employing frame doubling as necessary to bring up the lowest framerates to the refresh rate range of the display.

Compared to AdaptiveSync’s high standards, MediaSync’s requirements are something that should be attainable by a lot of monitors. So I wouldn’t be too surprised to see it show up on mid-range monitors, but even more than that, I expect this standard to be popular in the laptop market given how much media consumption is done on laptops these days.

Closing Thoughts

Wrapping things up, let’s talk about testing and logos for VESA’s new Adaptive-Sync performance standards.

Unlike DisplayHDR testing, OEMs cannot self-certify for AdaptiveSync/MediaSync compliance. Instead, all products must be sent to one of VESA’s approved Authorized Test Centers (ATCs), which the group already uses for things such as as certifying various DisplayPort devices. According to VESA, they are going this route because AdaptiveSync/MediaSync certification requires numerous specialized tools and significant know-how, which OEMs are unlikely to have access to. At the same time, it doesn’t hurt that this is another way which the new standards prevent shenanigans from OEMs by requiring a third-party prove that their products can meet the requirements.

That said, this does mean that certification will not come free. While OEMs do not need to pay VESA for the certification, they do need to pay the ATC for the testing. So the barrier to entry for a technically compliant display to get certified is very low, but it isn’t quite nil.

Once a display/product is certified, VESA has a unique logo for each program. For devices that pass AdaptiveSync conformance testing, the AdaptiveSync Display logo not only includes mention of the standard, but the display’s maximum refresh rate at its native resolution. This is to help communicate not only the maximum refresh rate of most monitors, but for the purposes of compliance testing on monitors with overdrive functionality, the refresh rate that the compliance testing was run at. Meanwhile MediaSync Display’s logo is more straightforward, and doesn’t make mention of refresh rates.

According to VESA, the final version of the standard was sent off to VESA members a few weeks ago. As usual for the group, they aren’t saying when we’ll see certified devices on the market since that’s up to their individual members. But, seeing as how there are some existing displays that should meet these standards, manufacturers should be able to promote their certification in short order – with updates to printed packaging to follow. Update: And indeed, LG is first out of the gate, announcing that both their 27GP850 and 27GP950 monitors are AdaptiveSync Display certified.

Finally, while the group hopes that they’ve knocked things out of the park with the first version of the AdaptiveSync/MediaSync standards, they’re also being quick to indicate that these standards aren’t set in stone. Should testing methods improve or OEMs find new and novel ways to pass certification, VESA is prepared to make further updates to the test suite. This is something they’ve already done once with DisplayHDR (which is now up to version 1.1), so there is precedent and experience here.

VESA Launches AdaptiveSync and MediaSync Perf Standards
Comments Locked


View All Comments

  • kpb321 - Monday, May 2, 2022 - link

    Offhand I'd expect they'd just use frame doubling to turn that 59/60fps into 118hz or 120hz and then be nicely in the range of the supported AdpativeSync refresh rates. Don't need to double things to run at 48 hz if you can just triple them to run at 72 hz or even quadruple them to 96 hz for media sync.
  • Zizy - Tuesday, May 3, 2022 - link

    Range of 60-144 is needed - but this is the minimum range in both directions. A screen can have 48-144, or 60-360, or 48-360 or anything.

    Also, the screen always runs at the same few ms of refresh per frame (at most 1000/144 = 7 ms, it can be lower for even faster screens). It just displays the same image twice if needed (or 3, 4 ... times). If the screen supports LFC (and these are required to), and if the screen doesn't flicker (again, covered here), you aren't going to even notice whether the screen displays 60 FPS content at 60 FPS or at 120 FPS (because the amount of blur will be from the 144 FPS maximum)

    Finally, note that 48-60FPS is required for the media tick, while a lot of movies are 24 FPS. But this range of 48-60 is still sufficient - movies will have the GPU simply repeating the frame twice while the screen runs at (effectively) 48 FPS. There is no LFC available but it isn't needed when the framerate doesn't vary much (or at all - movies).
  • Guspaz - Sunday, May 22, 2022 - link

    They require LFC support so 60-144 effectively means 0-144 in practice.
  • Infy2 - Monday, May 2, 2022 - link

    Interesting the bit about the need to test only at max refresh rate. I suppose various monitor reviewers have tested the lower refresh rates at fixed refresh rates rather than with AdaptiveSync active and frame rate limiter. If VESA's claim is true variable overdrive would be unneeded.

    This new AdaptiveSync standard however does not specify any maximum value for G2G times, so I guess some cheap VA panel with response time at worst 50ms can still meet the spec.
  • Oxford Guy - Tuesday, May 3, 2022 - link

    If a few transitions are very slow but the rest are okay, the benefits of VA may be worth it for some buyers. In particular, those who value a large contrast ratio but don’t want the issues OLED has.

    Others will prefer things like better colour/gamma consistency, within the reduced contrast gamut — which IPS provides. IPS pixels are also faster than VA, at least in the specific transitions VA struggles with.
  • Wereweeb - Monday, May 2, 2022 - link

    I read all of this and the only thing that went through my mind was "But what's the trick? How will the manufacturers trick consumers if the standard is actually meaningful?"

    Let's find whichever modern day Bonaparte was responsible for reforming VESA into an useful organization and put them in charge of reorganizing the USB mess.
  • limitedaccess - Monday, May 2, 2022 - link

    One of the "tricks" is setting 60 hz as the minimum threshold. I have concern that setting that bar may harm consumers in the long run if manufacturers end up settling for that as that would result in worse products than currently available.
  • Spunjji - Tuesday, May 3, 2022 - link

    Why? Frame-rate doubling covers you down to 30Hz
  • RSAUser - Saturday, May 7, 2022 - link

    I'm confused as to why that's an issue, GPU can handle 2x/3x rate, so if e.g. 24fps content, can display at 72Hz, every frame just lasts 3Hz.

    I would like lower frames than that even, but as long as ms refresh rate is fine, then drops down to 20/30fps for scenes will still be fine as monitor can just show a frame for longer (GPU support already exists for adaptive refresh rate).
  • haukionkannel - Monday, May 2, 2022 - link

    It all depends on...
    Vesa HDR system is so broken that you can put elephants through the holes.
    Hopefully they make better job this time... but I am not too sure that they will

Log in

Don't have an account? Sign up now